eycamplan-gizlilik

EYCamPlan Destek · EYCamPlan Support

EYCamPlan Destek

CCTV kurulumcuları için kamera hesaplayıcı, kat planı, kablo güzergâhı ve PDF rapor aracı · iPhone ve iPad · iOS 17 ve üzeri

İletişim

Soru, hata bildirimi veya öneri için: [email protected]. Hata bildirirken cihaz modelini, iOS sürümünü, ne yapmak istediğinizi ve ne olduğunu yazmanız çözümü hızlandırır. Mümkünse ekran görüntüsü ekleyin; müşteri bilgisi içeren planları göndermeyin.

Sık sorulan sorular

Yüklediğim kat planında mesafeler neye göre hesaplanıyor?

Fotoğraf veya PDF olarak eklenen plan başta ölçeksizdir. Düzenleyicide Kalibre aracını seçin, planda gerçek uzunluğunu bildiğiniz bir mesafenin iki ucunu işaretleyin ve uzunluğu metre olarak girin. Ölçek buna göre hesaplanır. Kalibre edilmemiş planda kablo uzunluğu ve kapsama konileri gösterilmez. Planda bulabildiğiniz en uzun bilinen mesafeyi kullanmak hatayı azaltır. Yeniden kalibre ederseniz tüm ölçüler yeni ölçeğe göre güncellenir. Boş ızgara planı hazır ölçeklidir (her kare 1 m).

Kablo uzunluğu nasıl hesaplanıyor?

(yatay mesafe + dikey iniş + 2 × servis payı) × (1 + fire yüzdesi)

Yatay mesafe, kameradan başlayıp dokunduğunuz noktalardan geçen güzergâhın plan üzerindeki uzunluğudur. Servis payı varsayılan olarak uç başına 2 m, fire %10’dur. Her ikisini Ayarlar’dan değiştirebilirsiniz; değişiklik yalnızca sonradan oluşturulan güzergâhlara uygulanır.

DORI mesafeleri nasıl hesaplanıyor?

Hesap IEC EN 62676-4 DORI piksel yoğunluğu eşiklerine dayanır (Tespit 25, Gözlem 62,5, Tanıma 125, Kimlik 250 piksel/metre). Eşikleri Ayarlar’dan değiştirebilirsiniz. Hesap, bozulmasız (rectilinear) lens modelini varsayar; sonuçlar planlama tahminidir, sahada doğrulayın. Sensör ön ayarları yaklaşık değerlerdir, üretici veri sayfası değeri değildir ve düzenlenebilir.

Projemi başka bir cihaza nasıl taşırım?

Proje ekranında ⋯ menüsünden yedeği dışa aktarın; .eycamplan dosyası oluşur. AirDrop, Dosyalar veya Mail ile diğer cihaza gönderin. Diğer cihazda kenar çubuğundaki içe aktar düğmesiyle dosyayı seçin. Not: Dosyaya dokunarak doğrudan açma henüz desteklenmiyor; içe aktarma kenar çubuğundan yapılır.

Verilerim bulutta mı?

Hayır. Uygulama internete bağlanmaz ve hesap gerektirmez. Veriler yalnızca cihazınızdadır; ayrıntılar için gizlilik politikasına bakın. Cihazı değiştirirken yedek dosyasını kullanın.

Raporda şirket adımı ve logomu nasıl gösteririm?

Kenar çubuğundaki dişli simgesiyle Ayarlar’ı açın ve şirket adı, telefon ve logoyu girin. Bunlar PDF rapor kapağında kullanılır.

Uygulama hangi dillerde?

Türkçe ve İngilizce. Dil, cihazın dil ayarına göre seçilir. Birimler şimdilik yalnızca metriktir.

Sürüm bilgisi

Bu sayfa EYCamPlan 1.0 için hazırlanmıştır. Gizlilik politikası: eycamplan-gizlilik.html

EYCamPlan Support

Camera calculator, floor plan, cable routing and PDF report tool for CCTV installers · iPhone and iPad · iOS 17 or later

Contact

For questions, bug reports or suggestions: [email protected]. When reporting a problem, please include your device model, iOS version, what you were trying to do and what happened. A screenshot helps; please do not send plans that contain client information.

Frequently asked questions

How are distances calculated on a floor plan I upload?

A plan added as a photo or PDF has no scale at first. In the editor choose the Calibrate tool, mark the two ends of a distance whose real length you know, and enter that length in metres. The scale is computed from it. On an uncalibrated plan, cable lengths and coverage cones are not shown. Using the longest known distance you can find on the plan reduces error. If you recalibrate, all measurements update to the new scale. The blank grid plan is pre-scaled (each square is 1 m).

How is cable length calculated?

(horizontal distance + vertical drop + 2 × service loop) × (1 + slack percentage)

Horizontal distance is the length on the plan of the route that starts at the camera and passes through the points you tapped. The service loop defaults to 2 m per end and slack to 10%. You can change both in Settings; changes apply only to routes created afterwards.

How are DORI distances calculated?

The calculation is based on the IEC EN 62676-4 DORI pixel-density thresholds (Detection 25, Observation 62.5, Recognition 125, Identification 250 pixels per metre). You can change the thresholds in Settings. It assumes a distortion-free (rectilinear) lens model; results are planning estimates, so verify on site. Sensor presets are approximate, not manufacturer datasheet values, and are editable.

How do I move a project to another device?

On the project screen use the ⋯ menu to export a backup; this creates a .eycamplan file. Send it to the other device with AirDrop, Files or Mail. On the other device use the import button in the sidebar and pick the file. Note: opening the file by tapping it is not supported yet; importing is done from the sidebar.

Is my data in the cloud?

No. The app never connects to the internet and needs no account. Data lives only on your device; see the privacy policy for details. When switching devices, use the backup file.

How do I show my company name and logo on the report?

Open Settings with the gear icon in the sidebar and enter your company name, phone and logo. They appear on the PDF report cover.

Which languages does the app support?

Turkish and English, chosen from your device’s language setting. Units are metric only for now.

Version

This page covers EYCamPlan 1.0. Privacy policy: eycamplan-gizlilik.html

Yorumlar